Contact Us

Xiamen Smark Bearing Co., Ltd

Tel: +86-592-6780643/ 5975776/ 5975807/ 5975817/ 5908751/ 5908761

Fax: +86-592-6106330

Mob: +86-15306000862

Email: gjpbearings@aliyun.com

Add: NO.52 to 58, Fanghu West Road, Xiamen, China

What Is The Purpose Of A Thrust Bearing?

The American Bearing Manufacturers Association (ABMA) is a for-profit association comprising more than 1,000 bearing manufacturers, dealers, and suppliers in the United States and Canada. The thrust bearings include NSK thrust bearings and a variety of other brands of thrust bearings, from self-aligning thrust bearings to thrust bearings, lubricated thrust bearings, and high-performance thrust bearings. 

Depending on the engine design, there are two bearings, the inner one is a large tapered roller bearing and the outer one is smaller and is the thrust bearing. There are bumper bearings that act on one side and one side that acts on both sides. The outer bearings are small and are located on both sides of the shaft, usually in the front or rear of an engine compartment or in the rear area. 

They resemble radial bearings, but have larger dimensions and are designed for greater loads in the form of a disc. Axial bearings are integrated into a specific main bearing unit and are usually located at the engine tip. They can consist of two or more bearings, usually one roller bearing and one radial bearing, or two roller bearings. 


If larger bearings are not an option, manufacturers can offer thrust bearings with hydrostatic lifting systems to enable the bearings to operate under heavy loads at low speeds. The selected bearing size is determined by the motor design, engine speed, and engine type. 

If you take the extra time to tighten the main bearing cap in this way, you help to align the thrust bearing surface with the crankshaft. If this occurs frequently enough, his face can erode, which can then affect it and damage the bearings. 

If the pressure of the line is uneven or if the torque converter has hydraulic power, forward shifting can cause the crank to jack forward and a direct load to fall on the rear – bearing thrust instead of the rear wheel. One can also speak of axial force since the force absorbed by the rolling bearing acts on it. They are called "handle" because they have little or no load in normal operation. 

In a tapered roller bearing, the ratio of axial to radial load is determined by the angle between the roller axis and the bearing axis. With respect to the radial ball bearing, the contact angle of the thrust bearings increases to 90 degrees. Consequently, only load axes occur, but even here radial loads must not be neglected. The mandatory bearing angles of 30, 40, and 50 degrees are mandatory, and even more so in the case of radial bearings. 

The Rolling Bearing Handbook provides a detailed description of the ABMA Class 00 bearings and thrust bearings, the most common type of bearings in the United States. 

The endgame is the total distance of the shaft that can be moved and is sometimes referred to as an up-axial bearing. It is defined as the distance between the end of a shaft and the point at which the applied axial load is balanced. This scale determines the type and number of thrust bearings required for optimal performance and service life. The pusher moves up and down the bearing rotor in a fixed time, usually about 1.5 to 2 seconds. 

Needle bearings are appreciated for their ability to roll over elements at high speeds, as in the case of a roller. Flooded or directional lubrication bearings are intended for machines where API requirements require balanced thrust bearings or where a bearing may be required for other reasons. 

Axial bearings are thrust bearings of certain construction and have an axial load-bearing capacity. They are used for bearing axles with ball or tilt type linings and are mainly used in low-speed applications. Ball bearings – like the ones shown below – cannot handle large radial loads, so they must be used with a ball bearing or a tilting pad type. 

As with radial or deep groove ball bearings, the load is distributed to the rolling element of the thrust bearing. This maximizes the contact area of the bearing, which helps to ensure its load-bearing capacity. The thrust bearings are aligned to the crank and thrust bearings, the thrust bearings to the tilt pad liners. 

A good example of axial loading is the propeller of a propeller aircraft driven by the propeller support and the thrust bearings of an aircraft driven by the propeller support. If the aircraft glides at a speed at which the crankshaft is straight, only the thrust of the propeller affects the shaft bearing, which allows a small forward and backward movement. 

The friction between propeller and thrust bearing can hardly be traced back to the actual installation vessel. By setting up thrust bearings as shown in the diagram, we give a very durable unit that allows wobbling – free rotation of the propeller shaft – by firmly supporting a large section of wire. 

Related News

Related Products