Contact Us

Xiamen Smark Bearing Co., Ltd

Tel: +86-592-6780643/ 5975776/ 5975807/ 5975817/ 5908751/ 5908761

Fax: +86-592-6106330

Mob: +86-15306000862

Email: gjpbearings@aliyun.com

Add: NO.52 to 58, Fanghu West Road, Xiamen, China

How To Remove Tapered Roller Bearing?

It is advisable to use a hydraulic press to drive and press the large bearing into the sleeve. The hydraulic method considerably facilitates the removal of the cone from the roller bearing and its attachment to the screw. In such cases, locking nuts and bolts facilitate assembly, as well as the installation of a locking nut on the shaft and the insertion of bolts above it. 

The pre-assembled bearing is equipped with a flange mount that allows it to be located in front – parallel or perpendicular to the shaft axis. The inner shell can be mounted directly on the floor shaft, or it can be mounted either directly on a drill rod or via an adapter on a standard shaft. If the bearing is located directly under the tapered seat of the adapter sleeve, the locking mechanism and the shaft sleeve should be loosened. 


For systems with sensitive imbalances or vibrations, it is recommended to use them with the shaft seat exactly on the ground. 

Most pillow block designs contain a self-aligning bearing type and do not require the precision fastening used in other bearing installations. If exact positioning is required to mount the bearing on the shaft or shoulder, use a clamp to determine the position of the bearings. 

When installing a tapered bore or spherical roller bearing, the radial inner clearance, which occurs gradually during operation, should be taken into account. First, stabilize the roll in the correct position and then insert a measuring device into the space between the rollers and the outer ring. Make sure that the distance between reel rows and outer rings is approximately the same (the). The thrust depth is described in Table 15 – 4, but the width of the inner ring corresponds to the diameter of each row of rolls. 

If the grease contains silver particles, the bearing should be replaced by a pitting roller. As you can see here, these bearings are usually tapered bores or spherical roller bearings and are usually tapered roller bearings. 

When you repack the stock with fresh fat, you do not want the old fat to spoil the new material. If they are misexecuted, the bearing shaft and housing damage candles, requiring expensive repair, and if the grease dries out, it can cause damage. 

When a torch is used, it changes the properties of the bearing steel and if it is stuck in the shaft and cannot be removed with a mechanical puller, you must throw it away. When the bear is installed in a fixed press – fit, heat the inner ring of the bear until it has locked at the back to facilitate removal. For smaller bearings, it is not necessary to help with disassembly by a puller. 

The easiest way to shorten the stack is to remove the inner bearing spacers so that the bearing spacers are located directly above the outer bearings of the barrel. Once the ring has been removed, you must lay out the bearings before submitting the distance to release. Follow step 6 of the instructions to use your inner bear and remove all material to get the required release, and then move on to the next step. 

You should be able to pull the hub and hub drum by hand, but you may find that you need a pack or washers to achieve the correct bearing setting. 

After you have noticed the fastening of the grease seal, turn the hub upside down and use a screwdriver to pull it off. Once the bottom bracket has come out of the hub, lift it up and put it aside with your hands, then carefully turn it over. 

It would be difficult to find a better way to turn the wheel to free it and carry a load that does not use lubricating tapered roller bearings. Stay on the spindle and push down as hard as possible until you find the right balance between turning the wheels to release and carrying loads that do not use large, conical roller bearings. 

Find the right balance between tapered and tapered roller bearings and find the best way to get the wheel off the rolling bearings. 

The linear movement of the roller element bearing is typically designed as a shaft on a flat surface. A common example is a fight against axial forces; common examples are bearings in drawers and support fittings. Flat bearings often consist of a roller and are attached to a cage, which is then placed between two flat surfaces. 

The ball has a groove designed to circulate the bearing shaft of the roller element from one end to the other during the movement of the bearing and is therefore referred to as the bearing. Special tools are required to remove mechanical and industrial parts such as bearings, especially when installed on rotating machine shafts. These tools, called bearing pullers, are made of steel, making them harder than the part they work for. 

Related News

Related Products