Contact Us

Xiamen Smark Bearing Co., Ltd

Tel: +86-592-6780643/ 5975776/ 5975807/ 5975817/ 5908751/ 5908761

Fax: +86-592-6106330

Mob: +86-15306000862

Email: gjpbearings@aliyun.com

Add: NO.52 to 58, Fanghu West Road, Xiamen, China

How To Measure Pillow Block Bearings?

A proper-sized pillow block bearing can be moved into the correct position to secure a locking device such as a pillow, pillowcase, or pillowcase while secured by a lock. 

The bearing required for a particular application depends primarily on the load and diameter of the installed shaft. The shaft height and the return height can be determined by measuring the middle shaft bearing of a pillow block bearing


The bore diameter can reach up to 5 '' ', but for heavy loads here in the MDS the available pillow block bearing type E offers a diameter of 3.5' '' and a return height of 5 '.5'. 

Environment, load, and size of the mounting shafts are important factors when choosing the right pillow storage for you. A good fit is required and it is necessary to wear a breed, but not too much or too little or not at all to have a good fit. 

The size and shape of the pillow block bearings can also be determined by the weight of the pillow and the load on the block. 

The pillow block bearings differ in the type of rolling element, which may include roller bearings consisting of cylinders, inner and outer ring bearings or undivided roller bearings. The split bearing housing consists of two parts that can be separated for cleaning and lubrication bearings replacement, while the fixed housing and split housing consist of one piece. For a proper fit, shaft and housing surface may need to be reconditioned prior to installing a replacement bearing, and the bearing may need to be removed from service sooner rather than earlier. 

The pillow block is a base that is used to support the rotating shaft with the help of compatible bearings and various accessories. To determine the best pillow block bearing for a specific application condition, the number of Plummer blocks, and the type of bearing. 

A pillow block usually refers to any slide bearing that includes a bearing with a diameter of at least 3 cm and a length of no more than 2 inches. A bearing in which the mounted shaft is less than 0.2 mm from the mounting surface and more like an assembled bore is called a "pillow block." The housing material of the pillow blocks is typically cast iron or cast steel. 

The contact surface must be parallel to the shaft axis or offset to the shaft axis and at least 1.5 mm above or below the horizontal axis. 

The bearings used in pillow block cases are normally self-aligning to compensate for angular errors. The mounting of the bearing base on the top or bottom of a flat surface (e.g. floor) allows for easy installation. 

A pillow block can contain several types of rolling elements, including ball bearings, roller, needle or needle bearings, as well as ball bearings and roller bearings. Plume blocks, which are bearing housings that supply the bearing, differ in that they are usually to be installed separately from the bearings in the pillow block case (e.g. top or bottom of the case). These are used for sliding, with ball bearings or needle bearings being used for rolling action. 

The basic application of both types is the same, namely to mount the bearing in such a way that its outer ring is stationary and at the same time allows the inner ring to rotate. Much has been said and done about the production of rolling elements and bearings for rolling and rotating equipment and the use of a pillow block. The assembly machine requires that everyone can slip and that if one fit fits tight, the other must be loose. 

The standard-fit of the housing is H6 (see table 1) and the radial ball bearing pin fits in the standard range from J5 to M5. Standard bearing sizes for the pillow block and ball bearing range from H4 to H5, with j5 ranging from m5 to j6. 

This is the standard-fit but can vary depending on the machine designer's understanding of the application and type of pillow block and ball bearing. 

To measure the flow, you will need a dial display with a diameter of less than one-thousandth of an inch and a length of at least 1.5 inches. The dial indicators must be accurate, as you will measure less than a thousandth of an inch, for example. Therefore, ask the bearing manufacturer to determine the right bearing class for your application. 

It is best if the weld material is not too large, but on large bottle racks it can cause some effort and it seems that it does not work as well as it should. Work in situations where you need to document the assembly connection, such as tightening threaded connections during assembly, even though there are thousands of mounting types of the same size. 

Related News

Related Products